Nowadays, e-cigarette players are challenging different tricks every day. In order to pursue better taste and more cloud, vapers are constantly creating different fancy coil windings.
How to clean your vape coils?
The fancy coil is made of a plurality of heating wires, and the heating area is larger than the ordinary heating wire. Therefore, it is superior to ordinary heating wire in both taste and smoke. However, there is a problem with the fever wire. Many newcomers are more worried about the heat of the silk carbon, how to do the heating wire carbon,
How to clean your vape coils this article will give you a detailed explanation.
When the heating coils were first introduced, many players could only look down on it because of the complicated winding process. With the advancement of the
electronic cigarette industry, there are already many fancy filaments of various materials that have been wound into heating coils, commonly known as fancy finished yarns. It makes it easier for players to experience the VAPE experience of fancy ribbons.
In fact, after a few days of use, the fancy silk will have more or fewer carbon deposits attached to the surface of the silk. In addition to being uncomfortable, it will also affect the taste. When sucking, there will always be some burnt paste. taste. What follows is the cleaning of the heating wire and the replacement of cotton. But in fact, when cleaning the fancy silk, there are still many places worthy of our attention. Today, I will simply talk about cleaning up the hot wire carbon, if your hot wire carbon is cleaned and maintained.
If your fever wire has been carbonized, it will have a more obvious paste. In general, we may recommend cleaning and replacing cotton for 1-2 days. Here you can try to clean the hot wire carbon with the method we said. After removing the cotton, install the nebulizer on the main unit. As in the case of burning, then adjust the voltage to about 3.0V. (The resistor used by the author is 0.16Ω and the power is adjusted to 55W). Don't adjust the power too high. Because of the high-temperature heating, the carbon will blast and burn to your hands. It is also possible to blow the entire heating wire directly. When heated, it can smell a strong burnt smell, which is caused by the carbon deposit on the surface of the heating wire. After the heating wire is burnt red, it is observed that the obvious carbon deposit is attached to the surface of the heating wire. After burning the red heating wire, you can release the ignition key, and then put the heating wire into warm water (water temperature about 40-60 °). Note that the main unit should not be exposed to water.
Be sure to remember here - don't ignite! Do not ignite! ! Do not ignite! ! ! Otherwise, the heating wire will be blown directly after being burned in water due to a short circuit.
Why use warm water?
In fact, the red hot wire is placed in water, and the heat treatment process of this rapid cooling process is called "quenching". If the temperature difference between the water temperature and the heating wire is too large, the heating wire will become brittle, that is, the heating wire will be easily broken. Directly affect the service life of the heating wire. After repeating the "quenching" several times, you can see that there are many black granular carbon deposits in the water.
Then, we can clean the heating wire with a brush for cleaning the heating wire. The carbon deposits are removed in a small gap between the wire and the wire. The bristles of this brush are usually made of stainless steel and brass, while stainless steel is harder than brass. When cleaning, be sure to pay attention to the following 2 points:
1. The intensity must be gentle, and you can't use "death power." Because the outer wire of the heating wire is generally relatively fine, the force is too strong, it is easy to hurt the outer wire.
2. When washing, be sure to follow a direction. Can't brush back and forth repeatedly. The author used to wash from left to right, then from top to bottom, and twice. Because the brush is repeatedly brushed back and forth, the silk which is complicated by the original winding process is disturbed, and the gap of the outer wrap is increased.
After that, the author likes to disassemble the entire atomizer and put it into an ultrasonic cleaner for cleaning. Let all the dirt hidden in the atomizer be cleaned out.
In the final step, after we have dried the atomizer, we can install the main unit and adjust the wire. Then let the heating wire cool naturally to room temperature.
In fact, this step, in addition to adjusting the heating wire, to see if the heat is even. There is still a "tempering" effect. It can improve the performance and service life of the heating wire.
In fact, if you use fancy silk, you may wish to choose a smoke oil with lower sweetness and better oil. This can directly reduce the amount of carbon deposited.
Fancy silks give players a higher quality VAPE experience, but due to the material and winding process, the price is higher than the ordinary heating wire. When we use fancy silk, we must know how to clean and maintain it daily.
Just like a car, you know how to appreciate but you also need to know how to maintain it. This not only prolongs the service life of the fancy wire but also allows the fancy silk to exert better performance and bring a better experience. Of course, this heating wire cannot always be used to clean carbon deposits. The life of a heating wire is still limited. Generally, you may need to change the heating wire after cleaning it twice, because saving money does not change the heating wire. The experience and taste will not be worth the loss. I hope everyone can find the fun of e-cigarettes and help people who are still smoking cigarettes bring a product for cigarettes!
